Detailing Tips & Tricks
|_Waterless Detailing Guide:
Waterless Auto Detailing
DRY WASH 'n GUARD® Uitra-Ion™ Waterless Carwash™
is extremely versatile; it can be used on any painted surface.
It is a superior detailing product for cars, RVs, boats, motorcycles,
airplanes, trucks, bicycles... the list goes on. It is also extremely
easy to use. Unlike conventional car wash and waxes, DRY WASH
'n GUARD® does not force you to work as
fast as possible. The following information is recommended by
Professional Detailers who use Dri Wash 'n Guard® in their
businesses and from the Reflections Detailing Association.
Waterless Detailing Exterior Vehicle
Where to Start:
Begin cleaning on the roof of the vehicle, the exception being
convertible tops, then move downward, doing the hood and trunk,
then the sides. Using this technique, you will apply DRY WASH
'n GUARD® Uitra-Ion™ to the least dirty areas of
the vehicle first, and cleaning the dirtiest areas last. Since
DWG™ products use
terry cloth towels for cleaning; your cleaning towels will stay
Applying Dri Wash 'n Guard®:
Use a small terry cloth towel, preferably white in colour, to
apply the DRY WASH 'n GUARD® to an area
approximately one (1) square metre. We recommend white terry
cloth because you can see the dirt more easily on the white
cloth as you are working. DRY WASH 'n GUARD®
forms a haze as you apply it; continue to work the product
onto the surface until the haze is almost gone. You do not
need to use hard pressure. The product does the work for you.
If you find a spot that is hard to remove, add a little more
Allowing the haze to form is very important, it is at this stage
that all the ingredients work on together to remove dirt and start
to form a protective bond. As the application towel becomes dirty,
fold it over and use a clean section.
Information About Terry Cloth Towels
Terry cloth is very absorbent, which is why it works well with
DRY WASH 'n GUARD®; dirt is literally
absorbed into the terry cloth after DRY WASH 'n GUARD®
lifts it from the surface of the vehicle. The terry cloth towels
should be clean prior to use, however, avoid using fabric
softener and bleach on the towels. The towels do not have
to be expensive, but they should be 100% cotton, so avoid
towels with special trim or binding that may not be made of
cotton. Terry cloth is very important in application process,
do not substitute other types of cloths, even if they are
clean. A typical sized vehicle will require one terry cloth
towel to complete the entire clean, polish and sealing process.
To help make your work a little easier, you can construct a "KwikPad"
by wrapping a strip of terry cloth around a sponge.
Wipe Down and Shine
Use a DWG™ Buffing Towel to remove the DRY WASH 'n GUARD®
haze. Excessive pressure is not required, just a thorough wiping
to remove the excess product.
Tips and Tricks for Exterior Vehicle
- Aim the DRY WASH 'n GUARD® spray onto
of the surface you are cleaning, and avoid spraying near cracks,
crevices and edges. This will prevent over-spray from getting
into seams and other areas that are difficult to access.
- If DRY WASH 'n GUARD® get on rubber
moulding, in the window areas, trunk, or under the hood, wipe
it down thoroughly For areas that are difficult to access,
such as door jams and creases, wet the application towel with
a spray of Dri Wash 'n Guard® and then apply the product
with the towel. This technique works well for grills, edges
of lights, and areas where body moulding and sheet metal come
- Streaking occurs occasionally due to humidity, contamination
of terry cloth towel by other products, or excess residue from
old wax or cleaners that were applied previously. To remove
the streaking, wet a terry cloth towel, wring it out, and then
wipe over the streak lightly. Buff with a DWG™ Buffing
Towel and the streak will be removed.
- Towels are reusable, use a washing machine on regular cycle
to wash the towels, and avoid fabric softener and bleach. We
recommend washing the towels separately from other laundry in
- Use a separate cotton terry cloth towel to apply Waterless
Carwash™ to your rims, and a separate cotton terry cloth
towel to apply Waterless Carwash™ to your vehicles duco.
This ensures that the towel used for your duco stays cleaner
and usable for longer.
- Although white is the best colour, any colour will do, ensuring
that the towels are 100% cotton.
Detailing Tyre Treatment:
Applying DWG™ All Weather Tyre & Exterior
Use DWG™ All Weather Tyre & Exterior Trim Treatment
regularly to clean and protect tyres. Tyres, like automotive paint,
will deteriorate after long exposure to ultraviolet rays. DWG™
All Weather Tyre & Exterior Trim Treatment will protect your
tyres from the harmful effects of UV exposure. You can use direct
spray onto the tyres, if you are careful to avoid over-spray.
Otherwise, use the trigger applicator to spray DWG™ All
Weather Tyre & Exterior Trim Treatment onto a terry cloth
towel or you can use a ‘kwik-pad’ that has terry cloth
wrapped around a piece of sponge. The first few applications of
DWG™ Tyre Treatment will remove a great deal of road grime,
dirt, and oxidized rubber from your tyres. Repeat the application
and wipe down procedure until the wipe down cloth does not get
dirty. This usually requires two or three applications when you
first use the DWG™ All Weather Tyre & Exterior Trim
Treatment. The All Weather Tyre & Exterior Trim Treatment
is not a "wet-look" or gloss product, it is designed
to keep your tyres looking new, without any artificial appearance.
The sidewalls of your tyres will last longer as a result of the
DWG™ All Weather Tyre & Exterior Trim Treatment.
Tips and Tricks for Tyre Treatment:
- Clean your tyres with DWG™ All Weather Tyre & Exterior
Trim Treatment before you clean your wheels, this will prevent
over-spray of tyre cleaner onto clean wheels.
- Use a toothbrush or similar sized brush to clean crevices.
This works especially well where the tyre and the wheel come
- When the tyres are completely clean, apply the DWG™
All Weather Tyre & Exterior Trim Treatment one more time
to add an extra layer of protection. This works especially well
if the car will be sitting for a few hours after the application.
- Spray a small amount of All Weather Tyre & Exterior Trim
Treatment onto a terry cloth towel and wipe down your windshield
- Use a separate cotton terry cloth towel to apply All Weather
Tyre & Exterior Trim Treatment to your tires, and a separate
cotton terry cloth towel to apply Waterless Carwash™ to
your vehicles duco. This ensures that there is no cross contamination
of product on the towel used for your duco, and your towels
used to apply Waterless Carwash™ stay cleaner and usable
Waterless Detailing for Wheels
Applying DWG™ Waterless Carwash™ to wheels:
Wheels are often overlooked during a typical vehicle "wash";
therefore they can become extremely dirty. Regular cleaning will
not only enhance the appearance of wheels, it will improve the
life span of the wheels and reduce pitting, rust, and corrosion.
If the wheels are extremely dirty, use a soft bristled brush to
gently remove caked on dirt and mud. Otherwise, spray Dri Wash
'n Guard® Waterless Carwash™ onto the wheels and clean
the wheels using the same techniques as cleaning the vehicle's
Tips and Tricks for Waterless Wheel Detailing
- Avoid spraying past the wheels onto the brakes; this can
affect the brake system.
- Use DWG™ Premium Metal Polish to clean alloy wheels,
then use DRY WASH 'n GUARD® Waterless
Car Wash to protect and shine the wheels.
- Use DRY WASH 'n GUARD® on wheels that
have clear coat or painted surfaces, also use DRY WASH 'n GUARD®
to clean chrome, chrome plated, and gold plated wheels.
- If in doubt about the composition of the wheels, use DRI
WASH 'n GUARD® on the wheels and DO NOT
use Premium Metal Polish.
|_Waterless Detailing for Windows and Glass:
Applying Dri Wash 'n Guard® Ultra-Ion™
Spray a clean terry cloth with a small amount of DRY WASH 'n
GUARD® Waterless Car Wash. Apply
the DRY WASH 'n GUARD®
directly from the towel; do not spray onto the surface of the
window, unless the window is extremely dirty. Use this technique
for both the inside and outside of the windows.
Tips and Tricks for Window and Glass Detailing
- Consider wiping down the windows twice using two separate
wipe down cloths. This will remove excess product and ensure
prevention of the prism effect.
- Automobile windows, mirrors, and home windows require very
little Dri Wash 'n Guard® to become absolutely gleaming…
when in doubt, use less product.
- DRY WASH 'n GUARD® is safe for both
factory and after market tinted windows.
|_Waterless Vehicle Interior Detailing:
Remove all loose articles from the interior, including
floor mats, any articles in door or seat storage areas, loose
change, papers and personal items. Start by vacuuming the interior,
including seat seams, between seats, under seats and between seats
and console area and the trunk area. Vacuum the headliner especially
if it is cloth. Vacuum the floor mats prior to applying carpet
Waterless Fabric, Carpet & Upholstery Detailing:
Use a light coat of DWG™ Fabric, Carpet & Upholstery
Treatment (FCU) on the interior carpet and the floor mats. Spray
the DWG™ FCU onto the carpet. Use a terry cloth towel to
remove the dirt from the fabric. Rather than using a rubbing motion,
just draw the cloth across the carpet, turning the cloth as often
as necessary to continue using a clean surface. This technique
picks up dirt more rapidly as the cloth absorbs more dirt. Then
wipe down with another clean dry terry cloth. For cleaning upholstery,
spray a light coat of DWG™ FCU onto the upholstery, then
use a rolled up towel to lightly scrub the surface. Turn the towel
often to continue using clean terry cloth. Follow this with a
second towel using the same technique. This will ensure that the
upholstery is clean and as dry as possible.
Tips and Tricks for Waterless Fabric, Carpet & Upholstery
- To remove stains, spray the DWG™ FCU directly onto
the stain, let soak for just a few seconds, then use a soft
bristled brush in a circular motion to scrub the stain. Then
use a terry cloth washcloth or towel to remove dirt and excess
Waterless Leather & Vinyl Detailing:
Leather upholstery requires a quality leather-cleaning
product. NEVER use water to clean leather products, it will cause
leather to break down and crack. Leather and vinyl should be treated
once a month; more if there is heavy wear. DWG™ Leather
& Vinyl Treatment will clean, condition, provide UV protection,
reduce static and reduce dust build up on your leather and vinyl.
Spray DWG™ Leather & Vinyl Treatment onto the surface
of the leather, then use a terry cloth wash cloth or small towel
to spread and clean the surface. As with other DWG™ products,
use a white terry cloth so you can observe the dirty areas becoming
cleaned. Buff with another clean terry cloth towel. For vinyl
treatment, use the same procedure as leather treatment. Notice
that DWG™ Leather & Vinyl Treatment does not make the
leather or vinyl appear shiny. The shine that other products will
produce on leather and vinyl is actually an oil residue that is
very bad for your leather and vinyl. This oil residue will attract
dust and dirt and will eventually cause cracking of the surface
of you leather and vinyl. DWG™ Leather & Vinyl Treatment
contains the all-inclusive benefits of UV protection, cleaner,
and conditioner; most other products do not.
Tips and Tricks for Waterless Leather and Vinyl Detailing:
- In hard to reach areas, spray the DWG™ Leather &
Vinyl Treatment onto your cleaning rag and not directly onto
the surface. This will prevent over-spray that may be difficult
- Remember to use Leather & Vinyl Cleaner on doors, arm-rests,
sun visors, and headliners where these areas are made of leather
|_Waterless Convertible Top Cleaning:
Applying DWG™ Upholstery, Fabric & Carpet
Use DWG™ Fabric, Carpet & Upholstery Treatment (FCU)
for cleaning your convertible top. To use FCU, spray onto a 2
ft by 2 ft section of the convertible top. Using a clean terry
cloth towel or washcloth that is slightly damp (this prevents
linting), drag the terry cloth across the area that you just sprayed.
If the cloth becomes very dirty, use a clean section of the cloth,
then drag the cloth back over the sprayed area in the opposite
direction. Buff the newly cleaned section with a clean terry cloth
towel and move on to another section. As with other cleaning procedures,
change terry cloth if the cleaning cloth gets too dirty. Let the
FCU do the work, don't try to exert extra pressure to remove dirt,
you will only grind dirt into the fabric. The first cleaning with
this procedure may require multiple terry cloth cleaning cloths,
due to the fact that the convertible top is rarely truly cleaned
by conventional car cleaners. Follow up cleanings will take less
FCU and less effort, especially if you clean your convertible
top once a month.
Tips and Tricks for Convertible Top Cleaning
- Maintenance cleanings can be done by using a damp (not soaking
wet) terry cloth towel, and once again drawing the terry cloth
first in one direction, then in the opposite direction.
Convertible Rear Window Detailing
Applying Dri Wash 'n Guard® Waterless Car Wash:
Clean the rear window just as you would any other car window,
with DWG™ Waterless Car Wash. Remember to wet a terry
cloth towel with the DRY WASH 'n GUARD® to apply
to the window, do not spray directly onto the window itself.
Use this technique for both plastic and glass convertible rear
windows. Once again, buff with a clean DWG™ Buffing Towel.
If you accidentally apply DWG™ Waterless Car Wash to the
fabric, use DWG™
Upholstery, Fabric & Carpet Cleaner to remove.
Tips and Tricks for Convertible Rear Window Cleaning
- The mere act of physically getting to the rear window can
be a trick in itself since many convertibles have little access
room. It is worth repeating here - a small amount of Wash 'n
Guard® goes a long way. You will encounter mostly dust mixed
with environmental air pollutants on the rear window; the window
will probably look cloudy or hazy before you start and this
will give the impression that the window is very dirty, when
in fact, the dust is usually removed very easily.
- Remember to use a terry cloth wetted with DRY WASH 'n GUARD®
and avoid spraying directly onto the window.
Applying Dri Wash 'n Guard® Tyre & Exterior
This can be a difficult area, especially in winter. If the wheel
wells are wet, or have caked-on mud, use a bucket and sponge to
clean the area. Avoid soaps, since you will be treating the area
with DWG™ products after drying the wheel well. Dry the
area with a towel, then apply DWG™ Tyre Treatment - this
versatile product works great on all plastic and rubber, IF the
wheel wells are plastic lined as many new cars are today. If the
wheel well is all metal, use DWG™ Waterless Carwash™,
this will protect the metal and reduce dirt build up in the future.
If the wheel well is quite dirty, but not so much so that water
is required, use a stiff brush to remove dirt, then use the appropriate
cleaning product for the material inside the wheel well.
Tips and Tricks for Wheel Well Detailing
- Use a stiff bristled brush if needed, however, do not use
a wire brush and make certain the brush is in good condition
so you don't scratch plastic or metal with sharp edged bristles.
- Remember to use DWG™ Tyre Treatment on plastic and
DWG™ Waterless Car Wash on metal.
- Use terry cloth to apply and wipe down the cleaning product.
|_Waterless Rubber and Plastic Detailing:
Applying DWG™ All Weather Tyre & Exterior Trim
Wash 'n Guard® All Weather Tyre & Exterior Trim Treatment
is designed to clean, polish and protect all plastic and rubber.
It will impart a clean surface without adding unnecessary shine.
Use a terry cloth towel to apply the product and wipe down with
a second, clean terry cloth towel. Unlike DWG™ Waterless
Carwash™, no haze forms with the DWG™ Tyre & Exterior
Trim Treatment. Because bumpers, rubber moulding, door and fender
guards, and plastic rear view mirror casings are in locations
where there are crevices and cracks, you should spray the Tyre
& Exterior Trim Treatment onto the terry cloth and then apply
the product. Use a second application to bring out a brighter
shine if desired.
Tips and Tricks for Waterless Rubber and Plastic Detailing
- You can also use a foam "brush" applicator, used
in painting, to apply the DWG™ All Weather Tyre &
Exterior Trim Treatment. The foam applicator will place the
product more precisely and there will be less Tyre Treatment
to wipe down.